|
| |
Personal Care | Products |
|
| |
|
| |
|
|
Products |
| |
|
|
|
| |
Fluoroaliphatic Phosphate Ester Fluorosurfactant |
| |
| |
MASURF FS-130EB is characterized as a 30% active fluoroaliphatic phosphate
ester fluorosurfactant in water/ethyleneglycol monobutylether solution.
MASURF FS-130EB is an FDA approved, water dispersible fluoroaliphatic
agent that imparts a high degree of oil and grease resistance to paper
and paperboard.
MASURF FS-130EB identified as a substance generally recognized as
safe in 21 CFR §176.170, can be applied by the size press, gravure
or roll coating methods, or as internal sizing. Oil and Water resistance
is obtained through normal drying. Curing at high temperature after
drying is not necessary. It also imparts a sizing effect, and water
resistance. The addition of MASURF FS-130EB finish to paper and paperboard
does not affect texture, color, lubricity, air permeability or strength
of the paper.
Masurf FS-130EB is a versatile Surfactant and Soil Resistant agent
for use in a wide range of applications. As an Oil
Well Stimulation Fluid ingredient, MASURF FS-130EB is an effective
foaming agent for alcohol/water mixtures; i.e. methanol, ethanol,
isopropanol in the presence of brine and hydrocarbon contamination.
Compare to Fluorad* FC-742.
MASURF FS-130EB is Non-Flammable, and does not contain or release
ozone depleting chlorofluorocarbons (CFC's), alkylphenol ethoxylates
(APE's), and does not release formaldehyde. FS-130EB does not contain,
release or degrade to perfluorooctane sulfonate (PFOS) or perfluorooctanoic
acid (PFOA).
INCI Name: DEA-C8-18 Perfluoroalkylethyl
Phosphate
|
| Typical Properties |
| Physical form |
Light tan liquid, with mild odor |
| Actives content % |
28 wt% minimum |
| Aqueous surface tension @25°C dynes/cm |
50.5@0.001%, 37.4@0.01%, 37.4 lowest |
| Specific gravity @25°C |
1.10±0.04 |
| pH |
10.0±1.5 |
| Viscosity @25°C |
<100 cps |
| Flash point |
>200°F |
| VOC content (volatile-water) |
0 |
| Storage |
Store above 32°F and below 100°F |
|
| Handling Information |
Refer
to the Material Safety Data Sheet (MSDS) available from Mason Chemical
Company for information on the safe use, handling and disposal of
this product. |
| |
| FDA Clearance |
MASURF
FS-130EB is identified as a substance generally recognized as safe
in 21 CFR §176.170 (Components of paper and paperboard in contact
with aqueous and fatty foods), and may be safely used as a component
of the uncoated or coated food-contact surface of paper and paperboard
intended for use in producing, manufacturing, packaging, processing,
preparing, treating, packing, transporting, or holding aqueous and
fatty foods, subject to the provisions of the section.
MASURF FS-130EB is certified to comply with the following guidelines
as listed in 21 CFR §176.170, where this product is represented as:
Diethanolamine salts of mono- and bis (1H, 1H, 2H, 2H-fluoroaliphatic)
phosphates where the alkyl group is even numbered in the range of
C8-C18 and the salts have a fluorine content of 52.4% to 54.4% as
determined on a solids basis.
For use only as an oil and water repellent at a level not to exceed
0.17 pound (0.09 pound of fluorine) per 1,000 square feet of treated
paper or paperboard, as determined by analysis for total fluorine
in the treated paper or paperboard without correction for any fluorine
which might be present in the untreated paper or paperboard, when
such paper or paperboard is used in contact with nonalcoholic foods
under the conditions of use described in paragraph (c) of this section,
table 2, conditions of use (B) through (H). |
| |
| Manufacturing Method |
| The fluoroaliphatic
component of MASURF FS-130EB is manufactured by the "telomerization"
process, which differs significantly from the Simon Cell electrochemical
fluorination (ECF) manufacturing process utilized by the 3M Company.
MASURF fluoroaliphatic products are chemically different from 3M's
and do not contain, do not release, and have not been shown to degrade
to the products found and cited by 3M in their press release and reports
to the EPA, namely perfluorooctane sulfonate (PFOS) and perfluorooctanoic
acid (PFOA). Additionally, the manufacturing facility for MASURF FS-130EB
does not utilize the EFC process in any of the products manufactured,
and there is no product or component contact with any EFC derived
materials in any step of the manufacture and/or distribution that
may result in PFOS/PFOA contamination. |
| |
| Substrate: |
Non-sized bleached Kraft paper 40g/m2 |
| Application Method: |
Horizontal type test size press 23g/m2 (Wet) |
| Drying Conditions: |
100°C x 10sec/drum dryer |
| MasurfFS-130EB
(solids basis) |
Oxidized
Starch |
Kit
Value |
Stockigt
Size (sec) |
| 0.3% |
None |
6 |
4 |
| 0.6% |
None |
9 |
8 |
| 0.15% |
3% |
6 |
2 |
| 0.3% |
3% |
8 |
4 |
| 0.45% |
3% |
10 |
4 |
| 0.6% |
3% |
11 |
9 |
*Fluorad is a Registered Trademark of the 3M Company. |
|
|
|
| |
|
|
|
| |
MAC V.031904 |
|
|
|
| |
| |
|
