|
| |
Personal Care | Products |
|
| |
|
| |
|
|
Products |
| |
|
|
|
| |
FDA Approved
Fluoroaliphatic Oil Resistant Agent |
| |
| |
MASURF
FS-115 is characterized as a 15% active aqueous fluoroaliphatic phosphate
ester fluorosurfactant solution. MASURF FS-115 is an FDA approved,
water dispersible fluoroaliphatic agent that imparts a high degree
of oil and grease resistance to paper and paperboard.
MASURF FS-115 can be applied by the size press, gravure or roll coating
methods, or as internal sizing. Oil and Water resistance is obtained
through normal drying. Curing at high temperature after drying is
not necessary. It also imparts a sizing effect, and water resistance.
The addition of MASURF FS-115 finish to paper and paperboard does
not affect texture, color, lubricity, air permeability or strength
of the paper.
Masurf FS-115 is a versatile Oil Resistant agent for use in a wide
range of applications, including Personal Care where MASURF FS-115
adds unique conditioning, wetting, lubricity and oil/sebum resistance
properties. When incorporated into make-up and mascara, FS-115/130EB
contributes to a "water-and sweat-proof top coat keeps the finish
smudge-free and color vibrant all day long."
INCI Name: DEA-C8-18 Perfluoroalkylethyl
Phosphate
MASURF FS-115 is Non-Flammable, and does not contain or release ozone
depleting chlorofluorocarbons (CFC's) or alkylphenol ethoxylates (APE's). FS-115 is available as
FS-130: 30% active in an aqueous solution.
|
| Typical Properties |
| Physical form |
Light tan dispersion, with mild odor. |
| Actives content % |
14.5 wt% minimum |
| Aqueous surface tension @25°C dynes/cm |
50.5@0.001%, 37.4@0.01%, 37.4 lowest |
| Specific gravity @25°C |
1.05±0.04 |
| pH |
9.0±1.5 |
| Viscosity @25°C |
<100 cps |
| Flash point |
None |
| VOC content (volatile-water) |
0 |
| Storage |
Store above 32°F and below 100°F |
|
| Handling Information |
Refer to the Material Safety Data Sheet (MSDS) available from Mason
Chemical Company for information on the safe use, handling and disposal
of this product.
|
| |
| FDA Clearance |
MASURF
FS-115 is identified as a substance generally recognized as safe in
21 CFR §176.170 (Components of paper and paperboard in contact with
aqueous and fatty foods), and may be safely used as a component of
the uncoated or coated food-contact surface of paper and paperboard
intended for use in producing, manufacturing, packaging, processing,
preparing, treating, packing, transporting, or holding aqueous and
fatty foods, subject to the provisions of the section.
MASURF FS-115 is certified to comply with the following guidelines
as listed in 21 CFR §176.170, where this product is represented as:
Diethanolamine salts of mono- and bis (1H, 1H, 2H, 2H-fluoroaliphatic)
phosphates where the alkyl group is even numbered in the range of
C8-C18 and the salts have a fluorine content of 52.4% to 54.4% as
determined on a solids basis.
For use only as an oil and water repellent at a level not to exceed
0.17 pound (0.09 pound of fluorine) per 1,000 square feet of treated
paper or paperboard, as determined by analysis for total fluorine
in the treated paper or paperboard without correction for any fluorine
which might be present in the untreated paper or paperboard, when
such paper or paperboard is used in contact with nonalcoholic foods
under the conditions of use described in paragraph (c) of this section,
table 2, conditions of use (B) through (H). |
| |
| Manufacturing Method |
The fluoroaliphatic
component of MASURF FS-115 is manufactured by the "telomerization"
process, which differs significantly from the Simon Cell electrochemical
fluorination (ECF) manufacturing process utilized by the 3M Company.
MASURF fluoroaliphatic products are chemically different from 3M's
and do not contain, do not release, and have not been shown to degrade
to the products found and cited by 3M in their press release and reports
to the EPA, namely perfluorooctane sulfonate (PFOS) and perfluorooctanoic
acid (PFOA). Additionally, the manufacturing facility for MASURF FS-115
does not utilize the EFC process in any of the products manufactured,
and there is no product or component contact with any EFC derived
materials in any step of the manufacture and/or distribution that
may result in PFOS/PFOA contamination. |
| |
| Performance Illustration |
| Substrate: |
Non-sized bleached Kraft paper 40g/m2 |
| Application Method: |
Horizontal type test size press 23g/m2(Wet) |
| Drying Conditions: |
100°C x 10sec/drum dryer |
| Masurf FS-115 (solids
basis) |
Oxidized
Starch |
Kit
Value |
Stockigt
Size (sec) |
| 0.3% |
None |
6 |
4 |
| 0.6% |
None |
9 |
8 |
| 0.15% |
3% |
6 |
2 |
| 0.3% |
3% |
8 |
4 |
| 0.45% |
3% |
10 |
4 |
| 0.6% |
3% |
11 |
9 |
|
|
|
|
| |
|
|
|
| |
MAC V.050801 |
|
|
|
| |
| |
|
